|
|||
|
|||
|
|||
• 317-7484 Communication Adapter III • 327-8981 (9-pin cable for Machinery) • USB cable • Olympian Electronic Service Tool (EST) v1.0 2011B • Perkins Electronic Service Tool (EST) v1.0 2013A • Perkins EDi 3.0 (old engine and genset diagnostic)
With this kit you can communicate with the ECMs through a communication data link, allowing existing and potential problems to be diagnosed, products to be configured, and data to be obtained for analysis. With this service tool users can: • View active and logged diagnostics. • View events where irregularities occurred and were logged by the ECM. • View the status of a group of parameters (temperatures, pressures, etc.) simultaneously. • Record and log performance data. • Graph a group of status parameters. • View the current configuration of an ECM. • Change ECM configurations. • Perform diagnostic tests. • Perform calibrations. • Print reports and diagnostic results. For some machine and engine products, additional functionality has been included with the service tool program. For programming protected parameters see Factory Passwords Generator software. 
|
2013-05-01
Landini McCORMICK AGCO Perkins DIAGNOSTIC KIT (CA3)
Download Perkins EST 2013A
Perkins EST 2013A
With this service tool users can:
• View active and logged diagnostics.
• View events where irregularities occurred and were logged by the ECM.
• View the status of a group of parameters (temperatures, pressures, etc.) simultaneously.
• Record and log performance data.
• Graph a group of status parameters.
• View the current configuration of an ECM.
• Change ECM configurations.
• Perform diagnostic tests.
• Perform calibrations.
• Print reports and diagnostic results.
• View active and logged diagnostics.
• View events where irregularities occurred and were logged by the ECM.
• View the status of a group of parameters (temperatures, pressures, etc.) simultaneously.
• Record and log performance data.
• Graph a group of status parameters.
• View the current configuration of an ECM.
• Change ECM configurations.
• Perform diagnostic tests.
• Perform calibrations.
• Print reports and diagnostic results.
More info: http://www.specdiag.com/perkins.html
Download Iveco E.A.Sy EASY 9.1 [2013]
E.A.SY (Electronic Advanced System) - allows simple diagnosis of the various electronic control units on the vehicle, using a communications module (ECI).
E.A.SY. software interface is designed to facilitate access to
tools, view functions and make diagnostic procedures clear and adaptable
to various needs.
The software for the E.A.SY platform provides a single, intuitive
interface, through which it is possible to consult a guide to repairs
organised by symptom.
With this service tool you can:
• Make active ECU diagnostic;
• Make parameter programming;
• Perform engine tests;
• View wiring diagrams.
More info: http://www.specdiag.com/iveco.html
With this service tool you can:
• Make active ECU diagnostic;
• Make parameter programming;
• Perform engine tests;
• View wiring diagrams.
More info: http://www.specdiag.com/iveco.html
ZF DIAGNOSTIC KIT (IXXAT DPA 05)
|
|||
|
|||
• DPA05 Interface • USB cable • RS232 cable • 9-pin cable • 9/6/3-pin cable • ZF-Testman Pro Development 10.5
ZF-Testman Pro checks the functionality of all electronically controlled ZF products. All transmission-specific data required for a fast and comprehensive diagnosis are retrievable by the ZF diagnosis system Testman. Supported commercial vehicle/special transmissions: • ASTRONIC (ASTRONIC 1, ASTRONIC 2, ASTRONIC Mid, ASTRONIC Lite) • ECOMAT (ECOMAT 1, ECOMAT 2/4, HP 260 CAN Converter) • INTRADER (INTRADER EST32, INTRADER EST42/48) • AVS • E-TRONIC • WSK EST 41/61 Supported commercial vehicle steering systems: • ZF Servocom RAS-EC (RAS-EC ISO, RAS-EC KWP) • ZF Servocomtronic (Servotronic F) Supported automobile car steering systems: • EHPS (BMW R50, OPEL EP2) • ZF Servolectric (BMW E85, APA E72, APA E90, VW PQ35/45 + Audi TT, VW PQ35-3) • ZF Active Steering (BMW E60 PL1, E70 PL4, E90 PL2) • ZF Servotronic (Servotronic F) Supported off-road driveline technology and asle systems: • ERGOPOWER (WG110-WG311, 2-3 WG-94, EST 117/125 - 119/126) • T7000 (T7100 EST38, T7200 EST38, T7300 EST38, T7000 EST45/57/57A) • ECCOM (John Deere, Claas) • T557 EST57A • HC 85 Diagnose: • Current errors; • Read error memory; • Delete error memory; • Read identification block; • Vehicle data sheet; Test Inputs and Outputs: • System-check standstill; • System-check run; • Test unit (indication of all digital inputs and outputs); • Indication of all digital and analog values such as speeds, currents and voltages; Repair support: • Tightening torques; • Setting data; • Special tools; • Test equipment; • Maintenance; • Repair work; • Pressures; • Circuit diagrams; • Electrical readouts; • PDF format; Vehicle configuration - depending on product all vehicle specific data can be stored or shift programs selected and adjusted. 
|
Download Hino Diagnostic eXplorer & Reprog Manager 3.1.2 [2013]
Hino Hino Diagnostic eXplorer & Reprog Manager 3.1.2 [2013]
• Acquire and delete trouble data;
• Link diagnostic trouble codes read from the ECU to corresponding diagnostic work flow sequences and directly view the required data;
• Obtain sensor conditions from the vehicle when trouble occurs;
• Monitor the sensors and actuators equipped on the engine and test the operation of solenoid valves by forcefully operating them;
• Simulate diagnostic work with only a PC;
• Automatically save fetched ECU data and analyze trouble based on the saved data even when the cause of trouble cannot be grasped;
• Reprogram the ECU’s program which is compatible with the reprogramming software.
More info: http://www.specdiag.com/hino.html
CLAAS DIAGNOSTIC KIT (CANUSB)
|
|||
|
|||
• CANUSB Interface • OBD2 cable • CLAAS CDS 6.0.8 • CLAAS MetaDiag© 2007 (Update 2013)
MetaDiag© 2007 - electronic diagnostic system used by service technicians to obtain information regarding possible faults and quickly identify defects. Supported models: 1X0-94, Ares, Arion, Atles, Axion, Axos, Celtis, Ceres, Cergos, Dionis, Ergos, Ergos 4x6, Fructus, Gamme T, Nectis, Pales, RB, Temis. Supported languages: English, German, Danish, Greek, French, Italian, Dutch, Portuguese, Russian, Spanish. CDS (CLAAS Diagnostic System) - allow defects to be identified quickly and the on-board management system to be configured and updated. Supported models: Mega-Medion N, Jaguar, Wuantum. Supported languages: English, German, French, Spanish, Bulgarian, Swedish, Russian, Romanian, Portutuese, Polish, Dutch, Italian, Hungarian, Croatian, Finnish, Danish, Czech. 
 
|
Download CNH EST 7.5
CNH EST 7.5
With this service tool you can:
• Check status of parameters;
• Retrieve faults;
• Run diagnostic tests;
• Make ECU and parameter programming;
• Monitor active and logged diagnostics;
• View and change ECU configuration;
• View diagnostic procedures and schematics.
• Troubleshoot problems;
• Use asist database;
• Run scope diagnostics;
E.A.S.y - additional engine diagnostic and download tool for connection directly to ECU to perform diagnostic, programming and ECU reload by K-Line protocol.
CNH Engine Download Tool operates from within the EST program to perform the following engine download operations:
• Provide Engine Control Unit (ECU) programing update capability;
• Provide blank ECU initialization and programming capability;
• Provide ECU programming reassignment for blank and other ECUs;
• Provide ECU download crash recovery.
More info: http://www.specdiag.com/cnh.html
Download Scania SDP3 2.14
Scania SDP3 (Diagnos & Programmer) 2.14.0 [1302]
cania Diagnos & Programmer 3 (SDP3)
communicates with Scania vehicles and Scania industrial and marine
engines. The program has been developed to support the electrical system
with CAN communication. The program is used for troubleshooting,
adjusting customer parameters, calibrations, conversions affecting the
electrical system and updating software in control units.
Our provided USB key contains 3 Levels:High Level used for Scania R,P,G,T,K,N series (buses, trucks) over 2004 year.
Industry & Marine Level used for industrial and marine engines.
Internal Level for developers used for Scania R,P,G,T,K,N series (buses, trucks) over 2004 year.
Subscribe to:
Posts (Atom)