Isuzu IDSS [2016] U.S. and Canada ONLY with 2017 trucks

Isuzu IDSS [2016]  

Isuzu Diagnostic Service System (IDSS) is a comprehensive diagnostic tool which houses Service Information (including Electrical Troubleshooting Manual), Scan Tool, Service Programming, Bulletins and some training to support all Isuzu manufactured products. The system utilizes a laptop in conjunction with an industry standard J2534 vehicle interface device. Updating the system software is accomplished via the Internet.

The IDSS supports Isuzu manufactured product models 1996-2017 year:

 • Stripped Chassis w/3.0L Diesel (4JJ1);
 • N-Series w/3.0L Diesel (4JJ1);
 • N-Series w/5.2L Diesel (4HK1);
 • N-Series w/6.0L Gas;
 • N/W Series w/5.2L Diesel (4HK1);
 • N/W Series w/6.0L Gas;
 • F/T Series w/7.8L Diesel (6HK1);
 • H/C Series w/7.8L Diesel (6HK1);
 • C-Series w/7.8L Diesel (6HK1);
 • N/W Series w/4.8L Diesel (4HE1);
 • FRR/WT5500 w/7.8L Diesel (6HK1);
 • N/W Series w/5.7L (CAL) Gas;
 • N/W Series w/5.7L (FED) Gas.

The reasons for the IDSS are:

 • Need for a comprehensive common support tool in one package:
  - Scan tool;
  - Service Programming;
  - Service Information and Bulletins.
 • Need flexible system to fit GM and Isuzu’s needs in medium duty business:
  - HP change;
  - PTO settings at the Dealer, Fleet and Port levels;
  - Data Monitor System (Fuel economy, codes, operation status etc.);
  - Diesel Particulate Filter testing for 2007i emissions;
  - Release timing control;
  - On-demand changes.
 • Need for Internet updating and internet communication to dealers.
 • View service information.
 • View electrical shematics.
 • View service bulletins (1984-2014).
 • Use scan tool for diagnostic and controller programming.

Supported languages: English.

More info: http://specdiag.com/isuzu.html
More info: http://specdiag.com/isuzu.html
More info: http://specdiag.com/isuzu.html

CAT DIAGNOSTIC KIT Communication Adapter III 317-7485 compatible with CAT ET 2016A

CAT DIAGNOSTIC KIT (CA3)

Caterpillar Communication Adapter III (CA3) - is a 100% genuine dealer tool manufactured in Canada, used to connect PC based service tool to Perkins equipment. This is the only recommended communication device for Perkins, and the only what has CAT Data Link (CDL) protocol required to properly communicate with a Perkins engines.

It will let you to communicate with the ECMs through a communication data link, allowing existing and potential problems to be diagnosed, products to be configured, and data to be obtained for analysis.

Isuzu Diagnostic Kit Global G-IDSS E-IDSS [2016]

ISUZU DIAGNOSTIC KIT (MX2)

Isuzu Diagnostic Service System (IDSS) is a comprehensive diagnostic tool which houses Service Information (including Electrical Troubleshooting Manual), Scan Tool, Service Programming, Bulletins and some training to support all Isuzu manufactured products. The system utilizes a laptop in conjunction with an industry standard J2534 vehicle interface device. Updating the system software is accomplished via the Internet.

More info: http://specdiag.com/isuzu-mx2.html

Scania XCOM 2.29 update

Scania XCOM - is a diagnostic tool to read, save and modify ECU data such as trouble codes, parameters, statistic data etc. VCI2/VCI3 interface is used to connect to ECU via CAN protocol.

Supported modification of ECU data of the following types:

 • EMS – Engine management system.
 • GMS – Gearbox management system.
 • RET – Retarder system.
 • AWD – All wheel drive system.
 • CLS – Clutch Control.
 • EEC – Exhaust Emission Control.
 • COO (COO7) – Coordinator.
 • BWS (BCI1) – Bodywork system.

Supported resolving trouble codes to text description for the following types:

 • EMS (S6, S7, S8).
 • GMS (OPC4, OPC5).
 • RET (RET1, RET2).
 • AWD (AWD1).
 • EEC (SCR1, EEC3).
 • COO (COO6, COO7).
 • HMS (HMS1).

Some interesting options:

 • AdBlue ON/OFF.
 • EGR ON/OFF.
 • Chassis ID/VIN Change.
 • Immobilizer ON/OFF.
 • Truck Power INCREASE.
 • ECU Recovery.
 • ECU Reset.
 • ECU Unlock.

Supported languages: English.

More info: http://specdiag.com/scania-xcom.html

Scania SDP3 2.26 update [2016]

Scania SDP3 2.25.0 [1603]
Scania Diagnos & Programmer 3 (SDP3) communicates with Scania vehicles and Scania industrial and marine engines. The program has been developed to support the electrical system with CAN communication. The program is used for troubleshooting, adjusting customer parameters, calibrations, conversions affecting the electrical system and updating software in control units.

Bodywork Interface Configuration Tool (BICT) is a software tool for the Bodywork Interface Configuration (BIC) function. This tool facilitates the connection of bodywork and body using the functions included in the vehicle’s electrical system. The logic programming is done in a BIC project, which in turn can contain several logic diagrams, to make the logic programming clearer. The BIC project can be saved and reused for more vehicles. BICT can be used both with and without connection to the vehicle. Without connection to a vehicle it is possible to create new projects containing logic diagrams and simulate logic diagrams. The BIC project can be saved and later used to write the BIC program to the control unit. With BICT connected to the vehicle it is possible to write a new BIC program to the control unit or update the existing BIC program in the control unit. You can also troubleshoot the BIC program in the control unit via guides in SDP3.

More info: http://www.specdiag.com/scania-vci2.html
More info: http://www.specdiag.com/scania-vci3.html